How to use the shaver/epilator. - Model ES-ED50, ES-ED70, ES-ED90

Before use

Changing the head

1. Remove the head while pushing the head release button.
2. Push the head until it clicks.
   
   
    

Using the bikini comb (ES-ED90/70/50)

• Place the bikini comb onto the shaver head and slide trimmer up.
  • When the bikini comb is in place, make sure the comb is in close contact with the skin.
    
    
     

Best hair length for epilation

• Trim your hair before epilating for the fi rst time or if you have not epilated for a long time. Hair removal is easier and less painful when the hair is short.

LED light

• The LED light comes on when the power is turned on. The light will remain on while the power is ON.

Select the mode

• Operation will change in order from “NORMAL” → “SOFT” → “OFF” each time the power switch is pressed.

NORMAL

• In NORMAL mode, epilation is performed in a short time with fast disc rotation speed.

SOFT

• SOFT mode will control the rotation speed of the discs, and minimize irritation at the time of epilation.
  • The green lamp will light up when using SOFT mode.
    
    
     

OFF

• The power will be switched OFF.

---

Epilating

Areas suitable for epilation

The epilator can be used on the  areas.

• 

For models ES-ED90/70/50, the epilator can be used on the  areas. Before epilating the bikini-line, be sure to put on your swim wear or panties, etc. and check the areas you wish to epilate.

• 

Using the epilator on areas other than those marked   may cause pain or skin trouble.

Areas not suitable for epilation

• The epilator should not be used on the inner side of the upper arms and areas such as elbows or knees which are prone to sagging.
  • 

Dry epilation

• Before epilating, wipe off water or sweat on your skin.

Wet/foam epilation

• WET epilation (epilating after wetting the skin and epilator and then applying foam) makes the skin softer so it is gentler to your skin when epilating.

1. Wet your skin.
2. Wet the discs and place a small quantity of liquid shower gel on the discs.
   • Always use shower gel when wet epilating.
   • Rinse any shower gel off of your hands.
3. Select the mode by pressing the power switch.
   • Foam is created. Foam makes the epilator slide better, so you can move it fast. 

• We recommend using the appliance in an ambient temperature range of 5 - 35 °C (41 - 95 °F). If used outside this range, the appliance may stop operating.

Epilating legs or arms

• Upwards from the bottom of the leg. Inwards from the outside of the arm.
  • 

Epilating underarms or bikini-line

• Move in several directions as underarm/bikini line hair grows in different directions. Stretch the skin with your fingers, and move slowly from inside to outside going against the flow of hair.
  • 

Shaving (ES-ED90/70/50)

Dry shaving

• Before shaving, wipe off water or sweat on your skin.

1. Attach the shaver head.
   • Confirm the bikini comb is detached.
2. Check that the outer foil is not deformed or damaged.
3. Select the mode by pressing the power switch.
   • Press gently so that the whole blade is in close contact with the skin and the surface of the blade does not move up and down.

Wet/foam shaving

• Shaving with soap lather makes the skin slippery for a closer shave.

1. Attach the shaver head.
   • Confirm the bikini comb is attached.
2. Check that the outer foil is not deformed or damaged.
3. Wet your skin and put shower gel on your skin.
   • Do not use shaving cream, skin cream or skin lotion as it will clog the blades.
4. Select the mode by pressing the power switch.

---

Foot Care (ES-ED90)

The basics of foot care

• Do not use the product for filing anything other than calluses and hardened skin on the feet.

Use on 

• Callus:  A callus is a hardened layer that forms through repeated pressure or abrasion.

Avoid using on

• Blister:  A blister is a fluid-filled, bean-sized bulge caused by shoes rubbing against the skin or horizontal bar exercises etc. It is caused by sudden stimulus to the skin.
• Corns:  A corn forms when a hardened layer thickens and extends deep into the derma. Applying pressure to a corn stimulates the nerves and can be very painful.
• Wart:  A wart is a raised area caused by a virus entering a wound and causing cells to multiply. Darkly-colored bumps may be visible and the affected area may be slightly painful.

Things to be careful of when filing

• Filing an area too deeply can cause it to become sore or inflamed.
• Filing too large an area can result in even larger calluses forming. Therefore, be sure to leave some of the hardened layer.

Using the foot care head

• The foot care head cannot be used in a bath or shower.
• Before use, be sure to fully charge the appliance.
• We recommend using the product within 30 minutes after bathing or showering. With the feet clean, wipe off any water on the skin. (Each use should be approximately 10 minutes (5 minutes on each foot, 10 minutes total for both feet))

1. Attach the foot care head.
   • Push down firmly until you hear a "click".
2. Press the power switch once.
   • NORMAL mode is recommended for rotation speed.
3. Bring the foot care head into contact with the skin, and begin filing.
   • Filing  a single location for a long time can cause it to become hot with friction. To avoid this, be sure to make small changes in the filing position while filing.
   • Filing should be performed about once every two weeks.

Toes and small areas

• Use your free hand to support filing.